- Jul 8, 2015
chevync20
Twelve Tip
We have a vessel not long ago i purchased which had plant 12V 8 determine wiring and plug at the start. My question is, i do want to work a Minn Kota Powerdrive V2 70 LB 24V engine, but must upgrade every thing to 24. I understand how-to line battery packs in parallel and show, but have to know the thing I should exchange. By wiring up in collection to 24V, try two line sufficient on plug? Do a 24V trolling engine have 4 wires? We have had 12V engines in past times, but never any 24V configurations. Anyone who can point me into the proper movement, i might greatly enjoy it.
The 70 pound 24V pulls a maximum of 42 amps, and so I believed the 8 measure wiring could well be enough. Any easy to follow backlinks was valued. We read some with only two wires many with three and four. Just want to guarantee I get everything purchased and ready for whenever motor comes. Thanks once more
- Jul 8, 2015
Eric Revo
Past Mossy Horns
- Jul 8, 2015
Dan in NC
Six Tip
- Jul 8, 2015
catfishrus
Twelve Tip
- Jul 8, 2015
chevync20
Twelve Pointer
- Jul 8, 2015
Eric Revo
Old Mossy Horns
- Jul 8, 2015
heavens hawk
Past Mossy Horns
As previously mentioned, 24v will move much less amps than 12v. Anytime the wiring had been sufficient for 12v, it will be adequate the 24v.
The sole different becoming in the event that you push the positioning on the batteries and increase the exact distance. Distance makes a difference. Or even, and you are clearly simply changing
- Jul 8, 2015
chevync20
Twelve Tip
- Jul 8, 2015
Mr.Gadget
Old Mossy Horns
- Jul 8, 2015
Mr.Gadget
Old Mossy Horns
As previously mentioned, 24v will move less amps than 12v. So if the wiring is enough for 12v, it would be enough for any 24v.
The sole exception are should you push the place for the batteries while increasing the exact distance. Length makes a difference. If you don’t, and you are clearly simply exchanging aside, never make the effort changing the wires.
- Jul 8, 2015
chevync20
Twelve Pointer
- Jul 8, 2015
Mr.Gadget
Past Mossy Horns
Yep consider they like liquids circulation. if you need a 2″ water line but only have 1″ you’ll be able to two traces to get the end demand.
Same manner with electricity. It is possible to work 2 traces both run 24v but visiting the exact same connect you can operated twice as much amps as just run one line say line x runs 50 amps but 2 outlines x/2 manage 25 amps each giving the 50 amps.
- Jul 8, 2015
chevync20
Twelve Pointer
- Jul 9, 2015
heavens hawk
Old Mossy Horns
24V pulls considerably recent than 12V. So if it absolutely was sufficient for 12, its ample for 24. You probably did capture that part best?
There are plenty of different gauges of wire that’ll work. The larger the cable the decreased voltage drop you have. Presuming a 20′ cable (40′ routine), 42 amp, 24V. 8 AWG needs to be good. I wouldn’t run heavier cable for a motor that will pulling much less recent than what the manufacturer intended.
Listed here is Minn Kota’s Conductor Gauge information: (click on the suitable connect)
Observe that the 12V 55lb. push model directly above yours draws considerably amps and needs big gauge line. Additionally notice the suggested circuit breaker is definitely more than the max amp draw for the engine. This is because you don’t want they to stumble every time you rotate the motor on large. Cannot put a 40 amp https://besthookupwebsites.org/her-review/ breaker on a 42 amp engine. Take into account that 95percent of the time you’ll not draw anywhere near 42 amps.
Write a Comment